- 您現在的位置：買賣IC網 > Datasheet目錄1 > 11-22/R6G6C-A01/2T (Everlight Electronics Co Ltd)LED RED/GREEN WATER CLEAR 1206 Datasheet資料下載
參數資料
| 型號： | 11-22/R6G6C-A01/2T |
| 廠商： | Everlight Electronics Co Ltd |
| 文件頁數： | 9/10頁 |
| 文件大小： | 361K |
| 描述： | LED RED/GREEN WATER CLEAR 1206 |
| 標準包裝： | 2,000 |
| 顏色： | 綠，紅 |
| Millicandela 等級： | 72mcd 綠，225mcd 紅 |
| 正向電壓： | 2V |
| 電流 - 測試： | 20mA |
| 波長 - 主： | 573nm，624nm |
| 波長 - 峰值： | 575nm，632nm |
| 視角： | 60° |
| 透鏡類型： | 透明 |
| 透鏡樣式/尺寸： | （內透鏡）圓頂圓形 |
| 封裝/外殼： | 1206（3216 公制） |
| 尺寸/尺寸： | 3.00mm L x 2.50mm W |
| 高度： | 1.50mm |
| 安裝類型： | 表面貼裝 |
| 包裝： | 帶卷 (TR) |
DATASHEET
SMD B
11-22/R6G6C-A01/2T
9
Copyright ?2010, Everlight All Rights Reserved. Release Date : 23-May-2013. Issue No: DSE-0008829 Rev.3
www.everlight.com
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30
or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30
or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60
5
for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
Pre-heating
150~200癈
60~120sec.
Above 217癈
60~150sec.
260癈 M ax.
10sec. M ax.
6癈/sec.M ax.
Above255癈
30sec.M ax.
3癈/sec.Max.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350
for 3 seconds within once in less than the
soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because
the damage of the product is often started at the time of the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering
iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will
not be damaged by repairing.
相關PDF資料 |
PDF描述 |
|---|---|
| 12-23C/R6GHBHC-A01/2C | LED RED/GREEN/BLUE CLEAR RA SMD |
| 1254-10SYGT/S530-E2 | LED 3MM ROUND YLW/GRN DIFF |
| 1383SDRD/S530-A3 | LED 5MM ROUND DEEP RED DIFF |
| 15-13D/R6GHBHC-A01/2T | LED RED/GRN/BLUE WATER CLR 1210 |
| 19-137/R6GHBHC-A01/2T | LED RED/GREEN/BLU WATER CLR 0603 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 11-22-R6G6C-QSANP-2T | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:Chip LED with Bi-Color (Multi-Color) |
| 11-22-R6SGAC-A30-2T | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:Chip LED with Bi-Color(Multi-Color) |
| 11-22SRVGC/TR8 | 制造商:Everlight Electronics Co 功能描述:3.0 x 2.5 mm Red / Green 60 32/21 mcd Water Clear LED |
| 11-22SURSYGC/S530-A2/TR8 | 功能描述:標準LED-SMD Brilliant Red Water Clear RoHS:否 制造商:Vishay Semiconductors 封裝 / 箱體:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明顏色:Red 波長/色溫:631 nm 透鏡顏色/類型:Water Clear 正向電流:30 mA 正向電壓:2 V 光強度:54 mcd 顯示角:130 deg 系列:VLMx1500 封裝:Reel |
| 11-22UYSYGC/S530-A2/TR8 | 制造商:Everlight Electronics Co 功能描述:CHIP LED W/ BI-COLOR WATER CLEAR - Tape and Reel 制造商:Everlight Electronics CO., LTD 功能描述:11-22UYSYGC/S530-A2/TR8 |
發布緊急采購，3分鐘左右您將得到回復。